spec no: dsai9084 rev no: v.4b date: may/09/2017 page: 1 of 5 approved: wynec checked: allen liu drawn: l.q.xie erp: 1203004259 1.6 x 0.8 mm smd chip led lamp part number: APT1608SYSCK super bright yellow features z 1.6 mm x 0.8 mm smd led, 0.75mm thickness z low power consumption z wide viewing angle z ideal for backlight and indicator z package: 2000pcs / reel z moisture sensitivity level: 3 z rohs compliant descriptions z the super bright yellow source color devices are made with algainp on gaas substrate light emitting diode. z electrostatic discharge and power surge could damage the leds. z it is recommended to use a wrist band or anti- electrostatic glove when handling the leds. z all devices, equipments and machineries must be electrically grounded. package dimensions notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.1(0.004") unless otherwise noted. 3. the specifications, characteristics and technical data descr ibed in the datasheet are subjec t to change without prior notice . 4. the device has a single mounting surface. the devic e must be mounted according to the specifications. attention observe precautions for handling electrostatic discharge sensitive devices
spec no: dsai9084 rev no: v.4b date: may/09/2017 page: 2 of 5 approved: wynec checked: allen liu drawn: l.q.xie erp: 1203004259 selection guide notes: 1. 1/2 is the angle from optical centerline where the lu minous intensity is 1/2 of the optical peak value. 2. luminous intensity/ luminous flux: +/-15%. 3. luminous intensity value is traceable to cie127-2007 st andards. absolute maximum ratings at ta=25c electrical / optical characteristics at ta=25c notes: 1. wavelength: +/-1nm. 2. forward voltage: +/-0.1v. 3. wavelength value is traceable to cie127-2007 standards. 4. excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradat ion or premature failure. notes: 1. 1/10 duty cycle, 0.1ms pulse width. 2. relative humidity levels maintained between 40% and 60% in pr oduction area are recommended to avoid the build-up of static electricity ? ref jedec/jesd625-a and jedec/j-std-033. part no. emitting color (material) lens type viewing angle [1] min. typ. 2 1/2 APT1608SYSCK super bright yellow (algainp) water clear 80 150 120 iv (mcd) [2] @ 20ma symbol parameter emitting color typ. max. units test conditions peak peak wavelength super bright yellow 590 nm i f =20ma d [1] dominant wavelength super bright yellow 585 nm i f =20ma ? 1/2 spectral line half-width super bright yellow 15 nm i f =20ma c capacitance super bright yellow 20 pf v f =0v;f=1mhz v f [2] forward voltage super bright yellow 2.1 2.5 v i f =20ma i r reverse current super bright yellow 10 ua v r =5v parameter values units power dissipation 75 mw dc forward current 30 ma peak forward current [1] 150 ma reverse voltage 5 v operating temperature -40c to +85c storage temperature -40c to +85c
spec no: dsai9084 rev no: v.4b date: may/09/2017 page: 3 of 5 approved: wynec checked: allen liu drawn: l.q.xie erp: 1203004259 super bright yellow APT1608SYSCK
spec no: dsai9084 rev no: v.4b date: may/09/2017 page: 4 of 5 approved: wynec checked: allen liu drawn: l.q.xie erp: 1203004259 APT1608SYSCK recommended soldering pattern (units : mm; tolerance: 0.1) reel dimension tape dimensions (units : mm)
spec no: dsai9084 rev no: v.4b date: may/09/2017 page: 5 of 5 approved: wynec checked: allen liu drawn: l.q.xie erp: 1203004259 packing & label specifications APT1608SYSCK terms and conditions for the usage of this document 1. the information included in this document reflects represen tative usage scenarios and is intended for technical reference on ly. 2. the part number, type, and specificatio ns mentioned in this document are subjec t to future change and improvement without notice. before production usage customer should refer to the latest datasheet for the updated specifications. 3. when using the products referenced in this document, please make sure the produc t is being operated within the environmental and electrical limits specified in the datasheet. if customer us age exceeds the specified limi ts, kingbright will not be respon sible for any subsequent issues. 4. the information in this document applies to typical usage in consumer electronics applicati ons. if customer's application ha s special reliability requirements or have life-threatening liabilitie s, such as automotive or medical usage, please consult with kingbright representative for further assistance. 5. the contents and information of this document may not be reproduced or re-t ransmitted without permission by kingbright. 6. all design applications should refer to kingbright application notes available at http://www.kingbrightusa.com/applicationnotes
|
